• Slower vs. aseptic due to moving the sterile tube fuser into position, obtain and install the correctly sized tubing holder, initialize the welder, load tubing, weld, cure time (~4-7 minutes total)
• Set up/use time multiplied by hundreds of welds a week affects overall productivity (e.g., 100 welds/week x 4 minutes = 6.67 hours operator time for welding)

Aseptic connectors are sterilized and ready to go in tubing/bag assembly, requiring only seconds to connect and actuate

• Connection can be made at any time or any place in the tubing
• Welder must be set up for correct tubing size and material
• Tube holders are gauged to specific sizes (e.g., 3/8” x 5/8”)
• Only the same-size tubing (same ID and OD) can be welded together

Single-use connectors are available that allow for flexibility between different types and sizes of tubing
No reducers required

• Capital equipment and ancillary equipment costs range from a few thousand dollars to tens of thousands per welder in each clean room
• Single-use blades cost
• Staff time for set-up and use or downtime if system jams or locks
• Back-up welder if needed
• Maintenance cost

Higher variable costs than blades
No capital expense

• Welders must be in good working order
• Welder manufacturer’s warranties for regular preventative maintenance of equipment
• Need backup welder during maintenance or out-of-service episodes

Single-use disposable connectors are ready to use
No maintenance required

• Very limited package
• Published studies on the impact of thermal welding process to the flow path of the tubing

Most manufacturers provide a published extractables package to understand potential effects on cell lines

• Nonconformance to manufacturer’s recommendations might raise contamination risk due to:
• Placing tubing with the incorrect diameter in the tube holder. This can cause small pinholes in the weld, due to pinching or squeezing the tubing out of the holder during the weld process
• Welding different tubing types together, which can lead to weld failure

Little to no contamination risk because validated aseptic connectors maintain a sterile boundary adjoining two single-use systems.

Welders require operator training to ensure proper technique, minimize errors and to safely use the equipment

Largely connect-and-go, self-contained components with minimal operator training required

• Not following manufacturer’s recommendations can lead to the following potential operator errors:
• Using wrong tube holders for size of tubing
• Using incorrect tubing: silicone, mismatched TPE
• Using incorrect tubing type setting on the welder
• Not using long enough tubing
• Putting tension on the tubing
• Inserting the blade incorrectly or reusing single-use blades

• Not following manufacturer’s recommendations can lead to the following potential operator errors:
• Using process fluids outside of the connector’s chemical compatibility specifications
• Not fully attaching connector to tubing
• Applying too much side load

• Minimum tubing lengths might be required to fit tubing into welder
• Must connect same materials (e.g., C-Flex to C-Flex)
• Costly C-Flex tubing is often used for welding
• Silicone can’t be welded because the material burns
• Must know each vendor’s type/size of tubing to ensure compatibility of supplies

• Any tubing length — no minimums required
• Connect to any type of tubing, including silicone, and different types of tubing (e.g., silicone to C-Flex)
• Connect different hose barb sizes (e.g., one side with ¾” hose barb and the other with a ½” hose barb)
• Genderless connectors eliminate the need to carry male/female components
• Connectors from the same family can be interconnected

• New sterile tube welders require onsite validation but come with a full weld validation package
• No new product contact material will be introduced into the process

Aseptic connectors are ready to use and have been validated for material biocompatibility, extractables, sterility, and leakage
New product contact material might need to be introduced and tested if the connector material has not been used elsewhere in the process

Weld on a new bag at any time or any place in the tubing line (e.g., during a perfusion process). Sufficient tubing length is required to make the weld

A pre-assembled, sterilized manifold of aseptic connectors facilitates adding additional lines to a process

Ensure sufficient room and ample tubing to place welder near the process due to the size of the welder

No extra space, materials or equipment required for connector use

~25 - 35 lbs. for welder

Negligible weight per connector